Magma

24 PCS Engine Oil Filler Set, 51042

2 litre funnel with 6 adaptors to fit a wide range of vehicles.
Allows for fast oil filling without spillage or waste.
Great for many late model vehicles with internal baffles.
For pouring oil where access is difficult.
Angled extension and adapters are made of plastic.
Contents:
1x Bayonet Adapter for Audi, BMW, Mercedes-Benz, Porsche, Volvo, Volkswagen
1x Bayonet Adapter for Toyota, Lexus 3.0 / 3.3 V6
1x Threaded Adapter M37x3.0 for Lexus, Toyota, Scion, Pontiac Vibe
1x Threaded Adapter M35x4.0 for Ford, Jaguar, Land Rover, Mazda
1x Threaded Adapter M32x3.5 for Acura, Dodge, Ford, Honda,  Jaguar, Jeep, Land Rover, Mazda, Nissan
1x Threaded Adapter M42x4.5 for Subaru
1x Threaded Adapter M30x3.0 for Dodge, Mitsubishi, Jeep
1x Bayonet Adapter for Ford, Mazda, Land Rover
1x Bayonet Adapter for Ford, Hyundai, Jaguar, Volvo, Mazda, Volvo
1x Bayonet Adapter for Volkswagen, Audi, Seat, Skoda
1x Bayonet Adapter for Dodge 5.7 / 6.1 / 6.4 Hemi, 3.6
1x Threaded Adapter M37x3.0 for Lexus, Toyota, Scion, Pontiac Vibe
1x Bayonet Adapter for Citroën C4 2.0, Peugeot 408
1x Bayonet Adapter for Mitsubishi Pajero V73, Volvo S80
1x Bayonet Adapter for Citroën C2 1.6L, C3 XR, C4 1.6, Peugeot 307, 206
1x Bayonet Adapter for Buick New Regal and Cadillac CTS 2.7
1x Bayonet Adapter for Buick Excelle
1x Bayonet Adapter for Volvo XC90, S80
1x Bayonet Adapter for Buick Sail 1.4, 1.6, 2.0
1x Universal Adapter
1x Oil Funnel 2L
1x Elbow
1x Angled Plastic Extension
1x Drain Fitting with Pressure Reducer

Made in China

M14x2.0 Spindle for Press and Pull Sleeve Kit, 50092-3

Pulling spindle with nuts and thrust bearings.

Size: M14x1.5 mm

Length: 350 mm

Material: carbon steel

Made in China

7 pcs Auto body repair set, 50209

Made of high-grade high-carbon steel.
It contains 3 models of ergonomic grippers, as well as adapters, necessary to straighten the car's dents.
Contains:
1pc standard bumping hammer
1pc pick and finish hammer
1pc reverse curve hammer
1pc curved dolly
1pc utility dolly
1pc double end hand dolly
1pc shrinking dolly.
Made in China

Standard engine cylinder hone 51 - 177 mm, 50723

•    Fast Accurate deglazing of cylinders of 2" to 7" in diameter
•    3, 4" long stone bars, 220 Grit Aluminum Oxide, replaceable
•    Adjustable collar to prevent stone breakage and control diameter
•    Use with 3/8" or 1/2" everyday portable drill or drill press
•    Flexible shaft to tool centering, adjustable tension on stone blades

6 mm 1/2" Dr. Stud Extractor, 50922-6

Designed for removing studs without damaging the threads.
Safe clamping due to 3 rollers. The extractors are the concentric roller bearing type that won't damage the thread on the stud.
Material: Cr-V
1/2" Drive (Hex 21mm).
Size: 6 mm.

Made in China

20 PCS Oil Sump Drain Plug Key Set, 20019B

Suitable for sump plugs on engine, gearbox and back axle.
Contents:
Square Male Keys: 7, 8, 10, 11, 12,13, 14mm and 5/16"
Hex Keys: 8, 9, 10, 12, 14, 17mm
Square Female: 10mm
Triangular Key: 10mm PSA
Security Spline Key: M16
VAG Plastic Plug Bit
VAG Torx T45
Flexible Head Bar 200mm

Made in China

M12x2.0 Spindle for Press and Pull Sleeve Kit, 50092-2

Pulling spindle with nuts and thrust bearings.

Size: M12x2.0 mm

Length: 350 mm

Material: carbon steel

Made in China

10 ton Hydraulic gear jaw bearing separator puller kit, 50457

Features:
Multifunctional gearbox for removal of gears and bearings. Included in the kit are separator  and three size brackets for three-ball bearings. It is suitable for a wide range of vehicles.
Contents:
10 Ton Hydraulic Ram
Twin Head Adapter for using as a 2 jaw puller
Triple Head Adapter for using as a 3 jaw puller
Two-way Cross Beam
3 x Gear Puller Legs/Jaws 100mm (4'')
3 x Gear Puller Legs/Jaws 150mm (6'')
3 x Gear Puller Legs/Jaws 200mm (8'')
2 x Main Rods
2 x Extension Rods
Center Extension Adapters 20 - 35 - 85mm
Bearing Separator 75-105 mm ...

Camshaft/Crankshaft alignment tool – Volvo, 50340

Contents:
Press tool – OEM No. 9995454
Holder – OEM No. 9995453
Camshaft alignment tool – OEM No. 9995452
Crankshaft TDC Timing pin – OEM No. 9995451
Applicable: Volvo models 850, 960, S40, S70 and S90

1/2” Dr. E20 Cylinder Head Wrench-Man, 50811

Features: For loosening and fastening cylinder head screws. Removing the injector no longer necessarily.
Ideally suited for commercial vehicles.
Profil: E-Torx.
Drive: Square, 1/2".
Applicable: MAN series F2000 / F90 / F8, MAN buses with D25 and D28 engines.

Made in China

M10x1.5 Spindle for Press and Pull Sleeve Kit, 50092-1

Pulling spindle with nuts and thrust bearings.

Size: M10x1.5 mm

Length: 350 mm

Material: carbon steel

Made in China

Camshaft sprocket puller for Ford, 50320

Features:
3 Legged puller specifically designed to remove the camshaft sprocket without causing damage to the pulley
Can also be used for pulling off the impeller
Applicable for Ford / Citroen / Peugeot and Mazda:
Ford: Focus (98- present 1.8D) CMax (1015), Courier (0002), Fiesta (0811), Fusion (0211), Focus (1115), Galaxy (0715), Kuga (1015), Mondeo (0615), SMax (0615), Tourneo Connect (0206), Transit Connect (0206)
Citroen: C3 III (1015), DS3 (1015), Xsara II (0015), Xsara Picasso (9910), C4 (0411), C4 II (1115), C4 Picasso/Grand Picasso (1015), C4 Air cross (1215), C5 (0005), C5 II (0408), C5 III (1015), DS4 (1115), Xantia (9801), Synergie/Evasion (9903), C8 (0215), Nemo (0810), Berlingo I/II (9911), Berlingo III (0815), Dispatch/Jumpy (9907), Dispatch/Jumpy II (0715), Relay/Jumper (0102)
Mazda: 2 (DE/DH) (0210)
Peugeot: 107 (0510), 1007 (0510), 206 (0109), 206CC (0507), 208 (1214), 306 (9902), 307 (0106), 307CC (0509), 308 (1114), 308CC (0914), 407 (0811), 407 Coupe (0712), 508 (1114), RCZ (1014), 2008 (1314), 3008 (1014), 4008 (1214), 5008 (1014), Bipper (0810), Partner/Partner Origin/Ranch I/II (0511), Partner III (0814),
Engine codes:
1.4D TDCi/Hdi: F6JA, F6JB, F6JC, F6JD, 8HP (DV4C), 8HR (DV4C), 8HS (DV4TED), 8HZ (DV4TD), 8HX (DV4TD), DV4C (8HP), DV4C (8HR), DV4TD (8HT), DV4TD (8HX), DV4TD (8HZ), DV4TED (9HS)
1.6D TDCi ECOnetic: HHJD
1.8D Turbo/TDCi: C9DC, RTN, RTP, RTQ, BHDA, BHDB, BHPA, C9DA, C9DB, C9DC
1.8 TDCi ECOnetic: KHBA
2.0 TDCi: AZBA, AZBC, AZWA, AZWC, G6DA, G6DB, G6DC, G6DD, G6DE, G6DF, G6DG, KLBA, LPBA, TXBA, TXDA,TXDB, TXWA, TYBA, TYDA, TYWA, UFBA, UFDB, UFWA, UKBA, UKBB, UKWA, UKDB, QXBA, QXBB
2.0 TDCi ECOnetic: KLBA, LPBA, TYBA
OEM 21-229, 303-651.
Engines Ford: Fiesta 1.8d TURBOB(98-), Focus 1.8d (98-).

Made in China

24mm Oil Filter Wrench For DSG Gear Oil Change, 50845
 
Features: For operation of the oil filter housing cover when changing the oil filter insert on the DSG gearbox.
Applicable: VW and VAG group vehicles.
No removal of batteries or battery holders.
VW specification: DSG oil change within the inspection interval.
Drive: Square, 1/2".
Output: Outside 12-point profile.
Wrench size: 24mm.
Length: 199 mm.

Made in China

2" Cylinder Hone Three arms, 50719

Suitable for small brake cylinders.
With three arms
Stone size: 50 mm
Capacity: ø32 - 88 mm (1-1/4” – 3-1/2”)

Made in China

28 pcs Press and sleeve master kit, 50605

Ideally for silent bearings, hydro bearings, bushings, ball bearings, simmerrings, ect.

Universal use for automobile, truck, municipally, country and forestery technology, ect.

Contents:
4 x step discs
4 x pulling spindle and nuts
8 x thrust bolts M10, M12, M14, M16,
20 x pressure sleeves:
Ø 44x34 mm; Ø 46x36 mm; Ø 48x38 mm;
Ø 50x40 mm; Ø 52x42 mm; Ø 54x44 mm; Ø 56x46 mm; Ø 58x48 mm
Ø 60x50 mm; Ø 62x52 mm; Ø 64x54 mm; Ø 66x56 mm; Ø 68x58 mm
Ø 70x60 mm; Ø 72x62 mm; Ø 74x64 mm; Ø 76x66 mm; Ø 78x68 mm;
Ø 80x70 mm; Ø 82x72 mm

Made in China