LÖTA

13 pcs 1/2”Dr. Special socket set, 011212930

Material: Cr-V Steel

Drive:1/2"Dr.

Size:6S-8S-10S-12S,8TS,10PT,

5PT-Female 10-12.5-14-19mm

5PT Male 10mm

12PT M16-M18

Feature:

6S Clutch Nissan,Renault

8S Cylinder head and balance shaft screw Nissan

8TS Balance shaft screw

12S Head bolts Nissan

10S Idle wheel centre screw Toyota

5PT

10mm Brake caliper

12mm Fuel pump Nissan

14mm GM brake caliper

19mm Brake caliper Citroen,Peugeot,Renault

10PT 20mm Rear Trailing arms Honda Civic ,CR-V

M16 Transmission gearbox drain plug Audi: A3 A4 A6 VW:Gof IV

M18 Half-axles VW

Special for the engine cylinder head nut and brake caliper.

Made in Taiwan

Internal snap ring pliers (Long arm), 096-7011

Special design for the retaining ring in the deep hole.
The most deep size: 56 mm

Made in Taiwan

2-Jaw Gear puller 80х80, 780-0008

Made of forged chromium-vanadium steel, rust resistant, heat treated.
High-precision hardened self-centering black-coated steel screw M18.
Galvanized parallel arms.
Applies even pressure to prevent damage.
Application: For removal of both internal and external gears, flywheels, rollers, etc.
Thigh depth: 80 mm
Axis width: 80 mm

Made in Taiwan

Introducing the Brake Spring Pliers, 210-0980-1, designed for easy assemble and disassemble of brake shoe springs in drum brakes.

• Zero damage to components during use.
• Features a socket end for removing springs and a grooved end for installing them.
• The jaw's unique sunflower-shaped design allows for a firm grip on drum brake shoes.

3/4” 6-pt. 44 mm Flank Impact deep socket, YT-9034644

Size: 44 mm
Overal lenght: 92 mm
Material: Cr-Mo

Made in Taiwan

1/2" Dr. Metal socket holder, 659-443216

L: 432 mm - 16 Pcs

Material: Steel

Made in Taiwan

Windscreen cutting wires triangle shape 1104725201

Due to the pointed cutting angle of 60T his triangular cut-out wire has a particularly good cutting ability. To avoid damages to the painted car body and to the interior this cutting wire should be used mainly for cutting easily accessible bonding’s.
Triangle cross section
Thickness: 0.6mm
Length: 22.5m

Made in Taiwan

Windscreen cutting wires  square shape 1104724201

Cutting wires is particularly suitable for cutting double glue beads or a very wide layer of polyuretane.
Square cross section
Thickness: 0.6mm
Length: 22.5m

Made in Taiwan

Torque Wrench 3/4" 65-450 Nm 418-T-300

The ratchet-type torque wrench enables to accurately limit the applied torque of fixture tightening.
It is made of chrome-vanadium steel which guarantees its durability and durability.
It has a mechanical tension of a wrench that, after reaching the required tightening force, jumps over a tooth giving distinctive sound.
The scale of the moments is located in the handle of the key and is adjusted by turning.
Once you have set the desired torque, lock the key at the end of the handle.
Square drive: 3/4" Dr.
Capacity: 65-450 Nm

N.W.: 3.770 kgs
G.W.: 4.580 kgs

Code: 505199

Made in Taiwan

1" Dr. 6-pt Flank socket 70mm

Material: Cr-V

Code: 505074

1" Dr. 6-pt Flank socket 80 mm

Material: Cr-V

Made in Taiwan

Antifreeze tester (For Ethylene glycol), 01A84906A

Easy to read indicator and designed for the popular modern Ethylene Glycol antifreeze. Suitable for use on OAT (Organic acid technology) antifreeze
Antifreeze Tester test at hot & cold temperatures.
Six floating discs for accurate reading. Number of floating discs indicates coolant strength.
Indicator range:  -7°C to -37°C ( +25°F to -34°F.)
Pure antifreeze will freeze at -12°C /10.4°F.
It permits to determine, with good approximation, the freezing point of the anti-freeze/coolant in the radiator and to reset the required protection level.
Floating orange disc shows over protection and loss of efficiency.

Made in Taiwan

AdBlue/DEF Tester (Diesel exhaust fluid), 01A84906

For the diesel engine emission system to function properly, the strength of the DEF solution must be maintained at 32.5% urea. Over time, the strength of the solution may change by evaporation, resulting in a reduction in the aqueous component of the solution or contamination. Both of these can lead to changes in the quality and strength of the DEF, which will be marked by the engine diagnostic system (DEF warning light).
Application:
For all vehicles equipped with diesel engines using urea solution at 32.5% as diesel exhaust (AdBlue®).
Gives a clear pass/fail result .
Accurate result regardless of sample temperature
Easy to use and read.
Attention! Always wash the inside of the appliance with distilled water after use.

Made in Taiwan

3/8” Dr. Adjustable torque wrench 5 – 25 Nm, 418-T-60-38

The ratchet-type torque wrench enables to accurately limit the applied torque of fixture tightening.
It is made of chrome-vanadium steel which guarantees its durability and durability.
It has a mechanical tension of a wrench that, after reaching the required tightening force, jumps over a tooth giving distinctive sound.
The scale of the moments is located in the handle of the key and is adjusted by turning.
Once you have set the desired torque, lock the key at the end of the handle.
Square drive: 3/8" Dr.
Capacity: 5 – 25 Nm (0.5 – 2.5 Kgs)
Made in Taiwan

4 in 1 Free way snap ring pliers set, 130003085

Description: This is a versatile tool that comes with interchangeable type kits that can be used for both internal and external retainers. Each type has a different angle, ranging from straight to 90 degrees. The spring housing has convenient gripping grips that make it easy to replace the retaining rings, retaining rings and rings.
The kit includes: Straight nozzle, 45° bent tip, 90° bent tip, pliers handles.

Made in Taiwan