AUTOMOTIVE SPECIALTY TOOLS

Diesel injector copper washer remover install tool, 50629
Size: inner hole 7mm

•     Designed for use on most Common Rail CDI injectors to remove copper washer sealing the base of the injector.
•     Suits most European cars using Bosch CDI fuel injection
•     Handy screw thread and expanding jaw design
•     Remove and install the copper washers on diesel injectors quickly and effectively with this special tool.
•     The reach of 230mm long is designed to install copper washers on deep seated injectors.
•     For removing and installing the copper wires on diesel injector.
•     Quick & effective. Reach - 230mm.

    For deep seated injectors.
    Manufactured from Chrome Vanadium.

Cam belt tension gauge, 50607

Suitable for belts of varying thickness.
Dual scales allows the measurement to be taken from either side of the tool.
Knurled knob measurement.
Lenght (approx): 85 mm - 100 mm
Wight: 80 mm

Made in China

Universal Tie rod wrench, 50444

Features:
Designed specifically for the removal of the direction of the steering rod.
The master tie rod tools easily replace inner tie rod ends.
Applicable to various vehicles: Mercedes Benz, BMW, Toyota, Honda, Ford,  Nissan , etc.

Engine Timing Tool Set BMW Mini, PSA 1.4 & 1.6, Citroen, Peugeot, 780-8162

Suitable for timing 1.4 & 1.6 Valvetronic direct injection petrol, chain drive engines, fitted in BMW Mini, Citroen and Peugeot vehicles.
Content:

• Camshaft Locking Tool - Inlet
• Camshaft Locking Tool - Exhaust
• Camshaft Alignment Clamp
• Crankshaft Setting Pin
• M6 Setscrews (4)
• Chain tensioner

Models:

• Mini One Coupe R56 (2006-2010)
• Mini Cooper Coupe R56 (2006-2010)
• Mini Cooper HB R55 (2007-2010)
• Citroën C4 (2008-2009)
• Citroën C4 Picasso (2008-2009)
• Peugeot 207 (2006-2010)
• Peugeot 207CC (2007-2010)
• Peugeot 308 (2001-2010)
• Peugeot 3008 (2009-2012)
• Peugeot 5008 (2009-2012)

 Engine Codes:

• N12
• N14
• EP3 (8FS)
• EP3C (8FR)
• EP6 (5FW)
• EP6C (5FS)
• EP6DT (5FT)
• EP6DT (5FX)
• EP6CDT (5FV)
• EP6DTS (5FY)

Code: 52046

Mede in Taiwan

Petrol engine timing locking tool set for BMW N42; N46, 50387

Contents:

• Intake & Exhaust Camshaft locking device with fixing screws

• Crankshaft Flywheel TDC Locking pin

• Rigid Chain Tensioner Tool

• OEM tools: 11 5 120, 11 9 190, 11 9 270, 11 9 291, 11 9 292, 11 9 293, 11 9 340, 11 9 350

Applications

• BMW E87 118i, 120i N46 engine

• BMW E46 316i, 316ti, 318ti N42 engine

• BMW E90/E91 318i, 320i, N46 engine

• BMW E85 Z4 2, 0l-N46 engine

Engine Codes

• N42 / N46

• B18 / B18A

• B20 / B20A / B20B

Easily remove diesel injectors with our comprehensive Diesel Injector Extractor Set 50633!

This kit is designed with various adaptors to fit most diesel injectors, including those from Delphi, Bosch, Denso, and Siemens. The set includes multiple slide hammers and pulling claws.

• Wide Compatibility: Adapters for Delphi, Bosch, Denso, and Siemens injectors.
• Multiple Slide Hammers: Includes 1.6 kg, 2.7 kg, and 5.1 kg hammers for various extraction needs.
• Durable Construction: Made with high-quality materials for reliable, long-term use.

14 Pcs Injection Puller Tool Bosch, Delphi, Denso and Siemens Diesel Injector Remover, 50348

Application:

Suitable for the fast and reliable removal of Bosch, Delphi, Denso and Siemens diesel Injectors.

Includes:

Comprehensive set of 1/2in.Dr Injector Sockets - 25, 27, 29, 30 mm

7 Injector Adaptors and Slide Hammer

Blow mold case for storage

Contains:

Impact Hammer: 3.6 kg

Overall length (. M handle) slide hammer: 510 mm

- Length of the handle: 110 mm

- Ball joint adapter

- Adapter: M14 x 1.5 for Delphi

- Adapter: M17 x 1 for Bosch

- Adapter: M20 x 1 for Denso

- Adapter: M25 x 1 for Siemens

- Adapter: M27 x 1 for Siemens

- Adapter: M27 x 1 for Bosch

- 4 slotted 6-point socket wrench inserts ( 100 mm long) for electrical unit: 25 - 27 to 29 - 30mm

- 10 mm hex bit application, 1/2 "drive

Made in China

5 pcs Trim fastener and molding removal set, 50241

Set includes five different sizes and styles of tools that allow easy removal of trim fasteners, moldings and wheel hubs.
Tools are made of plastic to prevent damage to trim, moldings, alloy wheels or vehicle paint.
Can be used on trim fasteners and moldings inside or outside

Windshield Removal Tool Set, 50220

This universal kit includes all of the specialised tools required to safely and quickly remove windshields from a wide variety of vehicles.
Item is supplied with a rubber gasket knife, cutting wire, two (2) handles, wire feeder tool, trim pad remover and molding release tool.

Set includes:

- Wire: Three strong galvanised steel wires braided to form one wire
- 2 pcs Wire gripping handles: Feed the wire through the hole in the wedge shaft. Loop it through the hole at the top of the shaft. Then back into the handle. Pressing the wedge back into the handle, the wire is held.
- Windshield removal tool: Cuts the vinyl adhesive compound around the windshield.
- Wire feeder tool: Designed for easy and flexible insertion of wire through polyurethane, allowing speedy removal of bonded windshield
- Trim pad remover: Place the tool under the edge of the door upholstery panel and insert it into the fastener as far as possible, then simply pry up.
1PC stainless steel wire with reel.
2PCS Wire gripping handles.
1PC Windshield removal tool
1PC Wire feeder tool
1PC Trim pad remover
1PC Windshield molding release tool

Made in China

Bearing separator 105 - 150 mm, 50132-4

Capacity: 105 - 150 mm
Bolt size: Ø 19 mm, 260 mm
Bolt thread: 3/4" x 16 UNF
Body thread: 5/8" x 11 UNC
Drop forged
Chrome finish

Bearing separator 75 – 105 mm, 50132-3

Bearing separator 50 - 75 mm, 50132-2

Capacity:2" 1/4"- 3 1/2". (50mm x 75mm)
Bolt 12.7 x 135 mm, thread 1/2" x 20UNF
Body thread 3/8" x 16UNC
HRC 38-45°
Forged
Chrome plated

Bearing separator 30-50 mm, 50132-1

-  Capacity: 30mm x 50mm  (1-1/4" to 2-1/4")
-  Bolt 9.5 x 125 mm, thread 3/8" x 24UNF
-  Body thread 3/8" x 16UNC
-  HRC 42-45°
-  Forged
-  Chrome plated

Labor Saving wrench, 50216

Labor Saving wrench adopt the highly effective and variable speed as a main drive, which function is small volume, light weight, Due to the big variable ratio, the less input power will come into being more output wrest distance, The product select high-grade alloy steel and the superior craft of heart treatment, firm and durable, high effective and saving, the appearance of using spray polishing, and have a good feeling. This products are used in kind of heavy-duty truck tire widely, and it is the necessary tool of auto repairman and the handy tool driver friends.

The biggest security output torque - 3800N.M.
Total length: 310 mm
Torque: 3800 Nm
Gear rate: 1:58
Impact socket: 32 mm; 33 mm

Made in China

Overhead valve spring compressor, 50109

Description: This overhead valve spring compressor is ideal for removing valve springs, spring retainers by compressing the valve spring retainer and exposing the valve keeper, remove keepers, uncompressing the tool then remove spring. It features a reversible jaw / adaptor and automatic cam-action locking to a re-determined setting.
Specifications:
Easy to operate
Cam action level design for secure valve spring locking into the tool
Allow valve springs and valve stem oil seals to be replaced with the cylinder head
Tool spring depth reach grips to retainer are adjustable to fit most large and small spring applications
For use on a wide range of OHV, OHC and CHV engines.
Not suitable for use on engines with deep seated valves

Made in China